Actuators for PIBCV

NovoCon S on AB-QM 4.0

The best results in indoor climate control are achieved by using the best possible actuators. The faster and more accurate the actuator responds to the control signal, the better the result.

Danfoss offers a wide variety of actuators fitting the AB-QM Pressure-Independent Balancing and Control valve.

NovoCon^® S

This innovative digital gear actuator with bus communication is designed to be directly connected to Building Management Systems (BMS) using BACnet or Modbus communication. It offers many features and benefits which you can read about here.

Danfoss NovoCon® digital actuator

Danfoss NovoCon® digital actuator connects heating and cooling systems to the hotel Building Management System (BMS) enabling smart, Internet of Things, solutions.

NovoCon digital actuator

AME and AMV

To achieve the best control performance with analog control signals, gear actuators should be used. These actuators control the position of the valve opening in a very accurate way.

AME gear actuators are controlled by a 0-10V or 4-20mA signal, while AMV actuators are controlled by a 3-point signal (open/neutral/close).

To achieve maximum control performance, geared actuators for AB-QM are equipped with automatic valve stroke detection.

TWA, ABN and ABNM

Thermal actuators provide a cost-efficient control solution for the AB-QM valves. The basic principle of these actuators is based on thermal expansion of a wax element. TWA-Z and ABN A5 actuators are controlled by an On/Off signal of a temperature controller, either heating the wax or not.
ABNM A5 actuators are controlled by a 0-10 Volt modulating signal of a temperature controller. The 0-10 V signal allows more accurate control possibilities.

Features and benefits

Broad product range

With actuators available for all AB-QM dimensions (DN 10 – 250), for all commonly used control signals (on-off, 0-10V, 4-20 mA, bus communication) and functional principles (thermal, analog gear, digital gear), there is always an AB-QM / Actuator combination that corresponds to the project requirements.

Danfoss PIBCV Documentary

We've asked Danfoss customers about their experience with the concept of pressure independent balancing & control valves (PIBCV). Hear all about the benefits and why they have converted from conventional balancing solutions to the PIBCV.

Product range

if (isSmallPicture) { ; } else if (isBigColumns) { } else { }

NovoCon® S Digital Actuator

With NovoCon® S Danfoss revolutionizes the way hydronic balancing and HVAC control work together. The first of its kind digital HVAC actuators are directly connected with a Building Management System (BMS). This enables System Integrators to design state-of-art, Internet of Things (IoT) solutions.

Documents

Promotional and Technical Documents


Type	Name	Language	Valid for	Updated	Download	File type
Brochure	AB-QM Actuator Selection Infographic - UK	English	United Kingdom	15 Jan, 2021	8.6 MB	.pdf
Brochure	Hydronic Balancing & Control product overview	English	United Kingdom	11 Nov, 2014	7.1 MB	.pdf
Brochure	Hydronic Balancing & Control product overview	English	Multiple	12 Dec, 2016	1.1 MB	.pdf
Brochure	Infographic - Actuator selection for AB-QM PICVs	English	Multiple	17 Sep, 2024	3.4 MB	.pdf
Case story	NovoCon - outstanding HVAC flexibility after office building renovation	English	Multiple	28 Sep, 2020	960.1 KB	.pdf
Brochure	NovoCon \| Digital actuator for HVAC	English	Multiple	20 Jun, 2017	772.5 KB	.pdf

Environmental Product Declaration (EPD) Documents


Type	Name	Language	Valid for	Updated	Download	File type
Product Environmental Information - BI	EPD ABQM 4.0 DN 15-32 & NovoconS	English	Multiple	27 Jan, 2023	4.1 MB	.pdf
Product Environmental Information - BI	EPD ABQM 4.0 DN 15-32 with AME 110	English	Multiple	27 Jan, 2023	3.7 MB	.pdf
Product Environmental Information - BI	EPD ABQM DN 40 -100 with AME 435 actuator	English	Multiple	27 Nov, 2023	2.5 MB	.pdf
Product Environmental Information - BI	EPD ABQM DN 40 -100 with NovoCon M actuator	English	Multiple	27 Nov, 2023	2.7 MB	.pdf
Product Environmental Information - BI	EPD AME 110 NL/NLX	English	Multiple	11 Dec, 2024	2.8 MB	.pdf

Software

Danfoss SET 365 software

Our advanced Danfoss SET 365 3D design software will help you to design and calculate HVAC systems with Danfoss products. A 1-year subscription is FREE available for students, designers and other interested professionals.

Danfoss SET 365 software

3D models and drawings

BIM library for MEP designs

Get your 3D BIM objects and start design HVAC control solutions.

Tender texts

NovoCon® S digital actuator

Modulating, high accuracy, geared actuator with field bus (BACnet MS/TP and Modbus RTU) connectivity used to control pressure independent balancing and control valves type AB-QM DN10-32.
Control signal digital: BACnet MS/TP, Modbus RTU
Control signal analog: 0-10V/2-10V, 0-20mA/4-20mA

Direct connection to 6-port ball valve actuator with position feedback signal (*1)

Direct connection to 2x PT1000 surface/immersed sensors and emission power indication (*2)

Direct connection I/O: 2x resistance, AO and AI (*3)

Actuator functionality is remotely accessible via the field bus:
- Design flow pre-setting
- Flushing the valve and terminal unit
- Error during closing intrinsic alarm reporting
- Alarm if CO6 6-port ball valve actuator is blocked, in manual override or disconnected (*1)
- Supply and return temperature readings, emission power indication (*2)
- Energy counter (kWh, MJ, kBTU) (*2)
- Alarm high/low deltaT and temperature sensors disconnected (*2)
- Alpha characteristics setting
- Speed selection 3/6/12/24 s/mm
- Opening/closing time selection from 18s to 700s
- Auto MAC addressing (BACnet only)
- Auto Baud rate detection
- Flow indication based on measured stroke in l/h

Eu.bac interchangeability approved in combination with PIBCV valve

Supply Voltage: 24V DC/AC 50/60Hz

Spindle position accuracy: ±0.05mm

Cables: Halogen free plug-in available in 1.5m, 5m and 10m length

Temperature sensors: plug-in 2x PT1000 surface or immersed 1.5m length

64 actuators can be connected to the same network

Supports BACnet service Change of Value (COV)

Supports remote Firmware updates

IP Class: 54

Stroke: 7mm

BACnet Testing Laboratories (BTL) listed BACnet MS/TP fieldbus device (*4)

Manual override function

Configuration tool available easy configuration, commissioning and firmware updates

Commissioning tool available for addressing, parametrization and hydronic continuous commission

Pulse input for Flow sensor to present real flow over the bus.
Warnings via field bus for: No flow and flow out of expectation
Full range from DN15-250.

Full range from DN15-250.
(*1) CO6 application
(*2) Energy application
(*3) Remote I/O application
(*4) Certification in Q2 2019

NovoCon® M digital actuator

Modulating, high accuracy, geared actuator with bus connectivity used to control pressure independent control valves type AB-QM NovoCon® DN 40-100.

Control signal digital: BACnet MS/TP, Modbus RTU
Control signal analog: 0-10V/2-10V, 0-20mA/4-20mA

Actuator functionality is remotely accessible via the fieldbus:
- design flow pre-setting
- flushing the valve and terminal unit
- error during closing/opening/calibration alarm
- LIN/LOG/α-setting characteristics setting
- selectable speed
- opening/closing time selection
- auto MAC addressing (BACnet)
- auto Parity detection (Modbus)
- auto Baud rate detection
- Flow and energy indication

Supply Voltage 24V ac/dc

64 actuators can be connected to the same network

IP Class: 54

Stroke: 20mm

Manual override function

Click on mounting

LED status indication

BACnet Testing Laboratories (BTL) listed BACnet MS/TP fieldbus device

Pulse input for Flow sensor to present real flow over the bus.
Warnings via field bus for: No flow and flow out of expectation
Full range from DN15-250.

NovoCon® L digital actuator

Modulating, high accuracy, geared actuator with bus connectivity used to control pressure independent control valves type AB-QM DN125-150.

Control signal digital: BACnet MS/TP, Modbus RTU.
Control signal analog: 0-10V/2-10V, 0-20mA/4-20mA

Actuator functionality is remotely accessible via the fieldbus:
- design flow pre-setting
- flushing the valve and terminal unit
- error during closing/opening/calibration alarm
- LIN/LOG/α-setting characteristics setting
- selectable speed
- opening/closing time selection
- auto MAC addressing (BACnet)
- auto Parity detection (Modbus)
- auto Baud rate detection
- Flow and energy indication
- Safety function in NovoCon® L SU/SD. Spring up or spring down for AB-QM DN125-150 valves.

Supply Voltage 24V ac/dc

64 actuators can be connected to the same network

IP Class: 54

Stroke: 50 mm

Manual override function

LED status indication

Pulse input for Flow sensor to present real flow over the bus.
Warnings via field bus for: No flow and flow out of expectation
Full range from DN15-250.

NovoCon® XL digital actuator

Modulating, high accuracy, geared actuator with bus connectivity used to control pressure independent control valves type AB-QM DN200-250.

Control signal digital: BACnet MS/TP, Modbus RTU.
Control signal analog: 0-10V/2-10V, 0-20mA/4-20mA

Supply Voltage 24V ac/dc

64 actuators can be connected to the same network

IP Class: 54

Stroke: 50 mm

Manual override function

LED status indication

Pulse input for Flow sensor to present real flow over the bus.
Warnings via field bus for: No flow and flow out of expectation
Full range from DN15-250.

AME 110NL/X - 2nd generation modulating Gear Actuators

The Danfoss AME 110 NL/NLX is precision engineered for high-performance with hydronic pressure independent control valves AB-QM in commercial HVAC applications. It offers precise water flow control, enhancing system efficiency and occupant comfort. Designed for seamless integration with Danfoss AB-QM valves, room controllers and advanced building management systems (BMS), the AME 110 NL/NLX stands out for its unique features that optimize performance and reliability.

Product Specifications

Mechanical Specifications:

Nominal Force: 150 N.
Stroke Length: 7.5 mm.
Operation Type: Modulating.
Resolution: Min. 450 steps (at 10% valve setting).
Position Accuracy: ±0.1 mm.
Speed of the actuator: 12 or 3 s/mm. providing flexibility in valve control.

Electrical Specifications:

Power Supply: 24V AC/DC, 50/60 Hz.
Control Signal: 0(2)-10V DC or 0(4)-20mA, providing flexibility in system integration.
Feedback Signal for NLX versions: 0(2)-10V DC, enabling accurate monitoring of valve position.

Features:

Logarithmic and linear characteristic settings available in the same product allowing for optimized control based on your specific application requirements.
Calibration: Automatic electronic calibration on power up to detect the opening and closing point of the valve.
Anti-Blocking/Sticking Function: Our gear actuator incorporates a selectable anti-blocking/sticking function, preventing valve blockages, ensuring smooth and reliable operation.
Actuator Mode Signaling: The actuator features LED signaling to indicate its operating mode, including running, standby, calibrate, and error modes, enabling quick and easy troubleshooting.

Direct or inverse acting actuator, allows for easy selection between direct or inverse acting modes, adapting to different control system requirements.
Manual Override Operation: In the event of power failure or maintenance, the actuator can be manually operated, ensuring continuous valve control.

Environmental Conditions:

Operating Temperature Range: -10°C to +55°C
Protection Class: IP54, providing protection against dust and water ingress from all directions, ensuring durability and longevity. This enables mounting of the AB-QM valves in all directions.
Humidity: 5% to 95% RH, non-condensing.

Compatibility:

Valve Types: Specifically designed for Danfoss Pressure Independent Control Valves, type AB-QM.
Halogen-Free Cable: The actuator comes with a 1.5m halogen-free cable as standard. Additional cable lengths of 2.5m and 5m are available.

Compliance and Standards:

EMC Directive 2014/30/EU EN 60730-1, EN 60730–2-14
RoHS 2011/65/EU standard EN IEC 63000
Low Voltage Directive - safety assurance is checked according to EN 60730-1, EN 60730–2-14

AMV 110/120 NL – Gear Actuators

3-point modulating geared actuator used to control pressure independent balancing and control valves DN 10-32.

Detection of valve stroke (NoLoad detection)
Power consumption: 1 VA running and 0 W standby
Visible stroke indicator
Halogen free cable: 1.5 m (5 m and 10 m)
Manual override operation
Supply Voltage: 24 V AC, 50/60 Hz
Speed: 24(12*) s/mm

*AMV 120 NL variant

ABNM A5 - Thermic actuators

Modulating thermal actuator used to control pressure independent balancing and control valves DN 10-32.

Control signal: 0-10 V
Valve stroke detection
Power consumption: 1 W standby
LOG(LIN*) characteristic
Halogen free cable: plug-in; 1 m (5 m and 10 m)
IP class: 54
Normally closed (open**) when de-energized
First open function (normally closed variant)
Visible stroke indicator
Stroke: 5(6.5 mm***)
Supply Voltage: 24 V AC, 50/60 Hz (24 V DC****)

*LIN variant available
**normally open variant available
***6.5 mm variant available
****24 V DC variant available

AME 435QM - for modulating control

The actuators AME 435 QM for modulating control is used with pressure independent balancing and control valve type AB-QM from DN 40 to DN 100.

Actuator shall have LED signalization
Actuator shall be able to mount/dismount on/off the valve without any tools needed
Actuator shall have efficiency improving and energy saving anti-oscillation function
Actuator shall have external reset/stand-by button
Easy electrical connection, snap on/of connection.

AME 55QM - Push / Pull actuators for larger AB-QM

The actuator AME 55 QM is used with pressure independent balancing and control large valve type AB-QM DN 125 and DN 150.

Actuator shall have LED signalization
Actuator shall be able to capture operational data
Actuator shall have possibility to be modulating or 3-p controlled
Actuator shall have reset option

AME 685-1 – Push / Pull actuators for larger AB-QM

AME 685-1 actuator is used together with large pressure independent balancing and control valves type AB-QM DN 200 and DN 250.

Actuator shall have LED signalization
Actuator shall have possibility to be modulating or 3-p controlled
Actuator shall have reset button

TWA-Q - Thermal actuator

On/off thermal actuator used to control pressure independent balancing and control valves DN 10-32.

Supply Voltage: 24 V AC/DC or 230 V, 50/60 Hz
Cables: PVC 1.2 m. , 2.5 m. and 5 m. + halogen free* 2 m.
IP-rating: IP54
Normally Closed or Normally Open variants available
First open function for the Normally Closed variant for easy installation
Visible stroke indicator
Power consumption: <2 W when activated

*halogen free cables available only for Normally Closed variant