Danfoss Link (Suport)

Demount old thermostat
If you have an old thermostat on your radiator, you need to dismount your old thermostats, before you can install Connect Thermostat. 
Watch video

Mount new thermostat and adapter
First, you need to identify which adapter is right for your radiator. Danfoss provides different adapters for different radiator valve types. Use the adapter selection guide by placing the different dimensions onto the valve to identify which adapter fits your valve.

The adapters supplied cover more than 90 per cent of all top mounted valves, both Danfoss and other brands. If none of the adapters fit onto your valve, it may be because your valve is old. In this case, we recommend that you buy a new valve.

Second, fit the correct adapter onto the valve. Insert batteries into your new Connect Thermostat and screw the thermostat onto the adapter and tighten. Leave mounting mode.

Now you are ready to create room and add devices on your Danfoss Link™ Central Controller.

Power outage on Danfoss Link™ Central Controller
If there is a power outage, the Danfoss Link™ Central Controller will turn on, once it gets power again and will connect to your installed devices.

If the Central Controller does not get power again:
• Connect Thermostat will continue on the temperature they were at when the power outage happened
• the Room Sensor will go into frost protection mode

Connect Thermostat or Room Sensor runs out of battery
When Connect Thermostat or Room Sensor is low on a battery, a battery icon will be shown in the display and the Central Controller will give you an error message. If a Connect Thermostat or Room Sensors runs out of battery, they will go into frost protection mode.
Connect Thermostats and Room Sensors use 2 x AA non-rechargeable batteries each.

The freer passage the radio signal from the Central Controller has, the farther it can reach. House walls, metal objects, special constructions and other obstacles weaken the signal. Your Central Controller will give an alarm if it cannot reach a device for more than 1.5 hours.

If there are obstacles between your devices, you may need to install a Repeater Unit to extend the signal. If necessary, you can extend the extended signal by adding another Repeater Unit as illustrated below. You only need one Central Controller for your home.

It can measure and control the temperature at a specific spot in your home.

If you place the Icon™ Room Thermostat close to your couch or away from a window, you ensure your desired temperature at this spot, because you optimize the actual temperature measurement in the room.

We recommend adding a Icon™ Room Thermostat in rooms with multiple radiators, because the Room Sensor balances the temperature across radiators based on the room temperature.

If your radiator thermostat is covered, e.g. by furniture, the Icon™ Room Thermostat  will ensure your desired temperature in the room.

Add the Icon™ Room Thermostat  to your Danfoss Link™ Central Controller in the same room as the Connect Thermostat you want the Icon™ Room Thermostat  to be connected to.

Energy savings are achieved through a reduction in room temperature.As a general rule, you can save 5% of energy consumption for every degree you lower the temperature at night. We recommend, you lower the temperature 3-4 °C at night and during working hours, e.g. from 21°C to 17°C. Also, activate vacation mode when you are on holiday.

When using Connect Thermostat, the average European saving potential is up to 30% on your heat consumption.

The older your thermostats are when exchanging them, the greater your energy savings will be.
Connect Thermostat was the first electronic thermostat ever to achieve the prestigious AA energy certificate from eu.bac.

Please go to our Danfoss Link™ App Helpdesk and get the assistance you need.

Open helpdesk

To ensure that the radiator thermostat can reach the set temperature quickly, we recommend a difference between Away/Asleep mode and At Home mode at max. 4 ˚C.

Danfoss Link™ offers a precise and energy efficient heating regulation by adapting itself to the heating system. This takes approximately one week after installation. Therefore, during the first week you can experience fluctuations as the thermostats are learning when to start heating to reach the specific temperature at the specific time (adaptive learning).

After this period, you can enjoy the perfect temperature in your home whenever you want it.

The Danfoss Link™ Central Controller works in all residential units up to 300 m² with a maximum of 50 units per Central Controller (1 Central Controller + 49 units).

You can connect up to 50 devices in total to Danfoss Link™ Central Controller and thereof max. 30 Connect Thermostat to Danfoss Link™. Danfoss Link™ controls up to 10 devices in one room.

Yes, if you have the Wi-Fi version of Danfoss Link™ Central Controller. You can download the app from either App Store or Google Play.

Find out if your Danfoss Link™ supports Wi-Fi here.

No.

Eco is a stand-alone product. You need to use Connect Thermostat for Danfoss Link™.

Danfoss ensures that all the devices in your home and the cloud service we provide to your smartphone are secure at all times. The Danfoss Link™ App is developed on a Home Banking platform and so the pairing of the Danfoss Link™ App to the Danfoss Link™ Central Controller is fully secure.